[[2011a]] #contents #define R OUT_C #define L OUT_A #define RL SENSOR_3 #define LL SENSOR_1 #define isBlack <40 #define isWhite >=40 #define NINETY 17 #define BALL 20 void go_straight(){ OnFwd (R+L); } void go_straight_s(){ OnFwd (R+L); Off (R+L); Wait (2); } void tr(){ OnFwd (L); OnRev (R); } void tr_s(){ OnFwd (L); Off (R+L); } void tl(){ OnFwd (R); OnRev (L); } void tl_s(){ OnFwd (R); Off (R+L); } void stop_moving(){ Off (R+L); Wait (100); } task main (){ SetSensor (RL, SENSOR_LIGHT); SetSensor (LL, SENSOR_LIGHT); int blackline = 0; while (1){ go_straight(); if (blackline >= 2) break; if (RL isBlack && LL isBlack){ PlaySound (SOUND_CLICK); blackline++; while (RL isBlack || LL isBlack) go_straight(); } } stop_moving(); // turn left while (1){ if (LL isBlack) break; tl_s(); } stop_moving(); // should be on the line, so trace it while (1){ if (RL isBlack && LL isBlack) { while (RL isBlack && LL isBlack) go_straight(); break; } else if (RL isWhite && LL isWhite) go_straight(); else if (RL isBlack && LL isWhite) tr_s(); else if (RL isWhite && LL isBlack) tl_s(); } stop_moving(); // should be at the end of the line /*while (1){ if (LL isBlack) break; tl(); }*/ tl(); Wait (NINETY); stop_moving(); // ready while (1){ if (Message() == 1){ Wait (300); go_straight(); Wait (BALL); } ClearMessage(); } go_straight(); //Wait (300); } #define R OUT_A #define L OUT_C #define SLIDE OUT_B #define RL SENSOR_1 #define LL SENSOR_3 #define NINETY 10 #define isWhite <40 #define isBlack >40 #define ANGLE 10 #define GOAL 500 void go_straight(){ OnFwd (R+L); } void go_straight_s(){ OnFwd (R+L); Off (R+L); Wait (1); } void go_back(){ OnRev (R+L); } void tr(){ OnFwd (L); OnRev (R); Off (R+L); Wait (1); } void tl(){ OnFwd (R); OnRev (L); Off (R+L); Wait (1); } void stop_moving(){ Off (R+L); Wait (100); } void out(){ OnFwd (SLIDE); Wait (50); Off (SLIDE); } void set_in(){ OnRev (SLIDE); Wait (50); Off (SLIDE); } task main (){ SetSensor (RL, SENSOR_LIGHT); SetSensor (LL, SENSOR_LIGHT); int blackline = 0; while (1){ go_straight_s(); if (blackline >= 2) break; if (RL isBlack && LL isBlack){ PlaySound (SOUND_CLICK); blackline++; while (RL isBlack || LL isBlack) go_straight_s(); } } stop_moving(); while (1){ if (RL isWhite) break; tr(); } stop_moving(); while (1){ if (RL isBlack && LL isBlack) { while (RL isBlack && LL isBlack) go_straight_s(); break; } else if (RL isWhite && LL isWhite) go_straight_s(); else if (RL isBlack && LL isWhite) tr(); else if (RL isWhite && LL isBlack) tl(); } while (1){ stop_moving(); SendMessage (1); tl(); Wait (NINETY); stop_moving(); Wait (300); tr(); Wait (70); go_straight_s(); Wait (GOAL); stop_moving(); out(); set_in(); go_back(); Wait (GOAL); tl(); Wait (ANGLE); Wait (ANGLE); stop_moving(); } } *メンバー紹介 [#d0cdd143] ・hiros ・show ・くまちゃん ・まえだ *マシン紹介 [#acac78f6] **ボール押し出し [#e162e410] #ref(ロボコン(ちびろぼ).jpg); できるだけマシンの小型化を狙いテニスボールを押し出せるようにした。 前の方に付いているとがったブロックはおもり兼押し出し棒。 #ref(ろぼこん(ちびろぼ)2.jpg); 幅は写真にもある通り極限まで狭くしてマシンそのものでボールを押し出す戦法で行くことにした。 #ref(ろぼこん(ちびろぼ)3.jpg); 車輪を外付けにするとボールを押し出すことができなくなるので、内側に付けることで解決した。 ただ車輪間の距離が狭くなると全体の安定感がなくなってしまい転倒しやすくなったので、マシン前後にだけ重心をかけるようにして横への転倒を防ぐようにした。 **ボールを運ぶ [#m4567511] #ref(ろぼこん(でかろぼ)2.jpg); ボールが中に入ると写真の丸で囲った部分が手前にスライドしていき、ボールを押し出しゴールインする仕組み。 #ref(ろぼこん(でかろぼ)3.jpg); マシンの前方がボールを受け取る場所になったので、センサーはマシンの後部に取り付けることにした。 #ref(ろぼこん(でかろぼ)4.jpg); 赤丸で囲った部分がボールをこぼさないための支えになっている。 当初はブロックにしていたが、ブロックだと耐久性に欠けていたので写真のパーツを使用した。 #ref(ろぼこん(でかろぼ)5.jpg); スタート時、既定の円に二台のマシンをセットしないといけないこともあり、なるべく小型化を目指した。 *プログラミング [#w9700e66] **ボール押し出し [#j5a06489] **ボールを運ぶ [#r8a0be8a] *感想と考察 [#a54e4aae] **hiros [#uaeafd10] **show [#p66b4bc6] **くまちゃん [#t5c20556] **まえだ [#pd2104ff] *コメント [#b65accf6] #comment 今日: &counter(today); 昨日: &counter(yesterday); 全て: &counter(all);